HiLook NS-0109P-60 8 Port Fast Ethernet Unmanaged POE Switch

Model: NS-0109P-60(B)

Who This Is For

Property managers specifying small CCTV systems who want to avoid running separate power supplies to each camera will find the HiLook NS-0109P-60 a practical fit. This 8-port unmanaged PoE switch delivers power and data over a single Cat5e or Cat6 cable to up to 8 cameras, with a total PoE budget of 60W shared across all active ports. It is designed for plug-and-play deployment - no software configuration, no managed switch complexity. It suits small commercial installs, retail fit-outs, or residential systems where a tidy, self-contained switch sits in a comms cabinet or on a desktop shelf. The single uplink port connects to a router or NVR, keeping the install straightforward. If your camera run count sits at 4 to 8 units and you need a clean, low-cost way to power them from one location, the NS-0109P-60 covers that requirement directly.

What This Switch Actually Does

Who Buys This Model

• Installers completing small commercial fit-outs: Retail stores, cafes, and small offices with 4 to 8 cameras benefit from a single PoE source point - one switch, one power point, cameras run on data cable alone.
• Residential system builders: Homes running 4 to 8 HiLook or Hikvision IP cameras to a central NVR use this switch to consolidate power delivery without running 240V to each camera position.
• Electricians and cabler completing CCTV subcontracts: The unmanaged design removes any requirement for IT-level switch configuration - connect and test without accessing management interfaces.
• Property managers upgrading legacy analogue systems: When replacing coax-based cameras with IP units, a compact PoE switch like the NS-0109P-60 slots into the existing comms location without requiring a full rack-mount upgrade.

Honest Assessment

The NS-0109P-60 does its job well within a defined scope: powering up to 8 standard IP cameras from a single location with no configuration overhead. The plug-and-play operation is genuine - there is nothing to set up on the switch side, which reduces commissioning time and removes a common source of field errors. The 60W PoE budget is adequate for most sub-8-camera deployments using standard dome or turret cameras drawing under 8W each. Where the NS-0109P-60 reaches its limits is on higher-draw devices. Cameras with active IR floodlights, PTZ units drawing 25W or more, or heated housing cameras may exhaust the 60W pool before all ports are populated. It also has no management features - there is no port isolation, no VLAN capability, and no traffic monitoring. For installs requiring those functions, a managed switch is more appropriate. Available through Security Australia, this switch suits straightforward installs where simplicity and cost efficiency matter more than advanced network control.

Before You Buy

Quick Fit Check

• Good match if: You are deploying 4 to 8 standard IP cameras drawing under 8W each and want a plug-and-play switch with no configuration required - total PoE draw stays comfortably within 60W.
• Good match if: Your install is in a small comms cabinet or desktop location where a compact unmanaged switch fits the space and budget without requiring managed switch features.
• You may need a different model if: Your system includes PTZ cameras, floodlight cameras, or other high-draw PoE devices that push total power above 60W - a switch with a larger PoE budget or per-port power allocation control will serve that deployment better. Browse the PoE switch range at securityaustralia.com.au for higher-budget options.

Key Features & Technical Specifications

Real-World Scenarios

How It Compares

• Choose this if: You need a no-configuration PoE switch for up to 8 standard IP cameras and the total power draw stays within 60W - the plug-and-play operation removes any need for IT-level setup.
• You may need a different model if: Your deployment includes PTZ cameras, floodlight cameras, or more than 8 camera positions - a higher-budget PoE switch or a managed switch with per-port power control will handle those requirements more reliably.
• Pairs well with: An 8-channel PoE NVR or a standalone NVR combined with this switch - the uplink port connects directly to the NVR's LAN port for a self-contained recording system.

Common Questions

1. Does this switch need to be configured before use?

   No. The NS-0109P-60 is an unmanaged switch - it requires no configuration at all. Connect your cameras to the PoE ports, connect your NVR or router to the uplink port, and power the switch on. PoE negotiation and data switching happen automatically. There is no web interface, no login, and no software to install.

2. Will this switch work with non-HiLook cameras?

   Yes, provided the camera supports IEEE 802.3af or 802.3at PoE. The NS-0109P-60 is compatible with any standards-compliant PoE IP camera regardless of brand. Hikvision, Dahua, Axis, and other IEEE-compliant devices will negotiate power and data correctly on any of the 8 PoE ports.

3. What happens if my cameras exceed the 60W PoE budget?

   Cameras will either fail to power on or drop offline when the 60W limit is reached. The switch does not damage connected devices - it simply stops delivering PoE to ports once the budget is exhausted, prioritising ports in order. Before commissioning, total the PoE wattage from each camera's datasheet to confirm your combined draw stays below 60W.

4. Will this switch work with a PTZ camera?

   It depends on the PTZ camera's PoE draw. Many compact PTZ cameras draw 15-25W each. Connecting a 25W PTZ to the NS-0109P-60 consumes 25 of the 60W budget, leaving only 35W for the remaining 7 ports - enough for 4 to 5 standard cameras. If your system is PTZ-heavy or includes multiple high-draw devices, a switch with a 100W or higher PoE budget is a more suitable choice. The NS-0109P-60, supplied by Security Australia, is best matched to systems using standard dome and turret cameras.

5. What cable should I use, and how far can I run it?

   Cat5e or Cat6 is recommended. The maximum cable distance per port is 100m - this is the IEEE standard limit for PoE over twisted-pair cable. Beyond 100m, signal quality and power delivery degrade. If a camera location exceeds 100m from the switch, a PoE extender or a second switch at an intermediate point is required.

6. Can I connect this switch to an NVR that already has built-in PoE ports?

   Yes, though it may not be necessary. If your NVR already has 8 built-in PoE ports, adding this switch creates a second network segment that requires the uplink port to connect back to the NVR's LAN port or a router. The NS-0109P-60 is most practical when used as the primary PoE source with a non-PoE NVR, or as a secondary switch to extend camera capacity beyond what the NVR's built-in ports provide.

Downloads & Resources

No downloads available for this product.