Dahua DH-PFA134 Water proof Junction Box

Model: DH-PFA134

Who This Is For

Property managers and installers specifying a tidy, weatherproof cable exit for Dahua cameras mounted on exterior walls, soffits, or rendered surfaces will find the DH-PFA134 a practical addition to any install. Rather than feeding cabling directly through the wall behind a camera baseplate - where water ingress and movement over time can compromise the junction - this waterproof junction box creates a sealed, dedicated cable entry point that keeps the installation looking clean and protects the cable termination from rain and moisture. It suits residential eave mounts, commercial building exteriors, and any situation where a flush wall cable entry is preferred over a surface conduit run. Installers working on multi-camera jobs particularly value having a consistent, professional finish at each camera position without the need for additional silicone work around the entry point.

What This Actually Does

Who Buys This Model

• Security Installers on Multi-Camera Jobs: Purchasing multiple units to standardise the cable entry finish across every external camera position on a residential or commercial project.
• Builders and Electricians: Specifying a neat, weatherproof camera rough-in during construction, before the camera itself is installed, to protect the cable termination during the build phase.
• Homeowners Upgrading an Existing Install: Replacing a poorly sealed direct-wall entry on an existing Dahua camera where moisture has been tracking into the wall or causing cable jacket deterioration at the entry point.
• Property Managers Maintaining Rental Portfolios: Standardising on a consistent, low-maintenance cable entry solution across multiple properties to reduce future service call-outs related to water-damaged cabling.

Honest Assessment

The DH-PFA134 does one job and does it well: it gives a Dahua camera wall mount a sealed, professional cable entry that protects both the cabling and the wall penetration from moisture ingress. For installers who take pride in the finish of their work, or for jobs where long-term reliability matters more than the cost of an extra accessory, this is a straightforward addition that prevents a common point of failure on outdoor installs. It also removes the need to pack silicone around a bare cable entry, which degrades and shrinks over time. Where it will not help is if your camera model uses a different baseplate diameter or mounting footprint - compatibility with specific Dahua camera models should be confirmed before ordering. This junction box is available through Security Australia and is best checked against your camera model's accessory list prior to purchase.

Before You Buy

Quick Fit Check

• Good match if: You are wall-mounting a compatible Dahua camera on an exterior surface and want a sealed cable entry that protects the wall penetration from moisture without relying on applied sealant.
• Good match if: You are installing multiple Dahua cameras across a site and want a consistent, professional finish at every camera position with the cable entry fully concealed beneath the baseplate.
• You may need a different model if: Your camera uses a different brand or mounting footprint - there are universal weatherproof cable entry covers and conduit entry boxes on the Security Australia site that may suit non-Dahua or mixed-brand installs.

Key Features & Technical Specifications

Real-World Scenarios

How It Compares

• Choose this if: You are mounting a compatible Dahua camera directly to an exterior wall and want a purpose-built, sealed cable entry rather than relying on applied silicone or surface conduit to protect the wall penetration.
• You may need a different model if: Your camera is ceiling-mounted indoors or uses a pendant/pole bracket - in those scenarios a junction box for wall cable entry is not the right accessory type, and a bracket-specific adapter or in-ceiling back box may suit better.
• Pairs well with: Dahua turret or dome cameras designed for wall or eave mounting, combined with a PoE switch or NVR that supports the camera model - the junction box sits between the wall and the camera base regardless of the recording infrastructure behind it.

Common Questions

1. Will the DH-PFA134 fit all Dahua cameras?

   No. The PFA134 is designed for specific Dahua camera models and is not a universal fit across the entire Dahua range. Compatibility depends on the baseplate footprint of your camera model. Dahua publishes an accessory selector tool that lists which cameras the PFA134 is confirmed to work with - check this before purchasing to avoid a mismatch on site.

2. Does the junction box work on both brick and timber surfaces?

   Yes, provided the correct fixings are used for the substrate. The PFA134 mounts flat against the wall surface, so it can be fixed to brick, rendered masonry, timber weatherboard, or concrete using appropriate wall plugs and screws for each material. The key requirement is that the box sits fully flush against the surface so the seal is effective.

3. Do I still need to seal around the junction box after fitting?

   In most cases, no additional sealant is required if the box is mounted flush and the camera base is correctly seated on top. However, on particularly exposed surfaces or where the wall has an uneven texture, a small bead of neutral-cure silicone around the perimeter of the box before mounting is considered good practice and adds a second line of defence against water tracking behind the housing.

4. Will this work for a ceiling or soffit mount?

   It can be used on a soffit surface that is effectively vertical or near-vertical, but the PFA134 is primarily intended for wall mounting. If your camera is going directly onto a flat horizontal ceiling surface, a different mounting accessory - such as a ceiling mount plate or recessed back box - is more appropriate. Check the Dahua accessory range at Security Australia for ceiling-specific options.

5. Does the junction box affect the camera's IP weatherproofing rating?

   No. The camera's own IP rating is determined by its housing and lens seal, not by the cable entry below the baseplate. The PFA134 protects the cable entry point and the wall penetration - it does not alter the camera's rated weatherproofing. The two work together: the camera body handles direct weather exposure while the junction box handles the cable entry seal at the wall.

6. Is the DH-PFA134 suitable for Cat6 cable or only Cat5e?

   The junction box is a cable entry housing, not an active component, so it is not cable-type dependent in the way a switch or NVR is. Both Cat5e and Cat6 pass through the entry opening. The relevant check is whether the cable diameter and connector size (standard RJ45 with boot) fits through the entry aperture, which they do under standard installation conditions.

Downloads & Resources

No downloads available for this product.