Hikvision DS-2XE6885G0-IZHS High Resolution Explosion-Proof Network Bullet Camera Series

Model: DS-2XE6885G0-IZHS

Who This Is For

For industrial engineers and security integrators who need certified camera surveillance in classified hazardous areas, the Hikvision DS-2XE6885G0-IZHS is built specifically for environments where standard IP cameras are not compliant. Carrying both ATEX and IECEx certifications, this camera is approved for gas and dust hazardous zones - think oil refineries, chemical processing plants, grain handling facilities, and offshore platforms. The 316L stainless steel enclosure resists corrosive atmospheres, while the IP68 rating keeps moisture and particulate out regardless of wash-down procedures or weather exposure. The motorized varifocal lens allows focal length adjustment without physically repositioning the housing, which matters when the camera is mounted in a confined or difficult-to-access zone. If your project requires certified explosion-proof surveillance with 8 MP resolution and the flexibility of a motorized zoom, this is a purpose-built solution for that brief.

What This Camera Actually Does

Who Buys This Model

• Oil, Gas & Petrochemical Facilities: Sites operating under classified zone requirements (Zone 1, Zone 2 gas or Zone 21, Zone 22 dust) need ATEX/IECEx certified equipment as a regulatory obligation - this camera meets that requirement in a permanent outdoor bullet housing.
• Chemical Processing Plants: Environments with corrosive vapour or aggressive wash-down schedules benefit from the 316L stainless steel enclosure, which resists chemical attack that would degrade standard aluminium camera housings over time.
• Grain Handling & Flour Milling Facilities: Combustible dust environments require dust-rated explosion-proof certification. IECEx coverage for dust hazardous zones makes this camera compliant for silos, conveyor areas, and processing floors.
• Mining & Quarry Operations: Remote or difficult-to-access installations benefit from the motorized varifocal lens, which allows focal length adjustment remotely after mounting without requiring re-entry to the camera position for physical lens adjustment.
• Industrial Security Integrators: Integrators tendering for hazardous area CCTV projects where the client specification mandates both international certifications and high-resolution imaging in a single network camera unit.

Honest Assessment

The DS-2XE6885G0-IZHS does one thing that most cameras cannot: it is certified for installation in gas and dust hazardous zones under both ATEX and IECEx standards. Paired with 316L stainless steel construction, IP68 ingress protection, and 8 MP resolution with a remotely adjustable motorized lens, it is a genuinely capable unit for the industrial scenarios it is designed for. The wide-range AC power input also simplifies deployment into existing plant electrical infrastructure. Available through Security Australia, this camera suits integrators who need documented compliance certifications as part of a project submission or site audit trail. Where it is not the right fit: for non-hazardous industrial or commercial outdoor applications, standard IP67 bullet cameras deliver comparable image quality at significantly lower cost and with greater flexibility in power options including PoE. The weight of approximately 4 kg and the AC-only power supply also mean mounting and cabling require planning that a standard bullet camera installation does not.

Before You Buy

Quick Fit Check

• Good match if: Your project is in a classified hazardous area (gas or dust zone) and your specification requires ATEX and IECEx certified surveillance equipment - this camera carries both certifications in a permanent outdoor bullet housing.
• Good match if: The installation environment involves corrosive atmospheres, chemical exposure, or high-pressure wash-down, and you need an enclosure material rated beyond standard aluminium alloy - the 316L stainless steel housing is built for exactly these conditions.
• You may need a different model if: Your site is a standard industrial or commercial outdoor environment without a hazardous zone classification - a conventional IP67-rated outdoor bullet camera will deliver comparable or better imaging flexibility at lower cost and with PoE support, and a wider range of models is available at securityaustralia.com.au.

Key Features & Technical Specifications

Real-World Scenarios

How It Compares

• Choose this if: Your installation is in a classified hazardous zone (gas or dust) and requires ATEX and IECEx certified equipment with high-resolution imaging and a corrosion-resistant stainless steel housing - there is no substitute for certification compliance in these environments.
• You may need a different model if: Your site does not carry a hazardous area classification - a standard IP67 or IP66-rated outdoor bullet camera will provide comparable or higher imaging flexibility, PoE support, and a much lower installed cost. A wider selection of outdoor bullet models is available at securityaustralia.com.au.
• Pairs well with: An industrial-grade NVR with H.265+ decoding support and sufficient storage capacity for 8 MP multi-camera retention, connected via a managed network switch rated for industrial environments.

Common Questions

1. Does this camera meet ATEX certification requirements for Zone 1 gas environments?

   Yes. The DS-2XE6885G0-IZHS carries both ATEX and IECEx certifications covering gas and dust hazardous scenarios. When specifying for a particular zone classification, confirm the camera's specific Ex marking against your site's hazardous area drawing to ensure the zone rating aligns - ATEX certification covers defined zone categories and the installation must match the documented zone classification.

2. Does this camera support PoE?

   No. The DS-2XE6885G0-IZHS runs on AC 100 V to 240 V only and does not support Power over Ethernet. Each camera position requires a dedicated AC power feed. In hazardous area installations, cable glands and conduit sealing at the enclosure entry points must also comply with the zone's cabling requirements - this should be confirmed with your electrical engineer during the design phase.

3. Why is 316L stainless steel specified instead of standard stainless steel?

   316L stainless steel contains molybdenum, which gives it significantly better resistance to chloride pitting and crevice corrosion compared to 304-grade stainless steel. In coastal industrial environments, chemical processing plants, or any site where chloride compounds, acids, or oxidising agents are present in the atmosphere, 316L outperforms standard grades over time and reduces the risk of enclosure degradation affecting the certified integrity of the housing.

4. Will this camera work in combustible dust environments as well as gas zones?

   Yes. The IECEx certification covers both gas and dust hazardous scenarios. This makes it suitable for grain handling facilities, flour mills, and other sites where combustible dust is the classified hazard rather than flammable gas. As with gas zone installations, the specific dust zone classification on site must be matched against the camera's certification documentation before installation.

5. How does the motorized varifocal lens work in practice for hazardous area installs?

   The focal length is adjusted remotely through the camera's software interface rather than by physically rotating a lens barrel on the camera. In hazardous area installations where accessing the camera after mounting requires a permit-to-work, safety isolation, or specialist PPE, being able to fine-tune the field of view from the control room during commissioning - without a return visit to the camera - reduces both time and safety exposure. Note that physically repositioning the camera housing still requires a site access procedure.

6. What storage and NVR should I pair with this camera?

   Any Hikvision-compatible NVR with H.265+ decoding support and sufficient channel capacity will work. At 8 MP resolution, each camera generates a significantly higher bitrate than a standard 2 MP or 4 MP camera, so storage planning should account for the higher per-channel bitrate even with H.265+ compression applied. For multi-camera hazardous area projects, Security Australia can assist with NVR and storage sizing recommendations based on your channel count and retention requirements.

7. What is the operating temperature range of this camera?

   The confirmed operating temperature range is -40°C to 60°C. This covers extreme cold climate installations including refrigerated facilities, high-altitude sites, and northern hemisphere winter conditions, as well as high-temperature outdoor industrial environments. At the upper end, 60°C ambient temperature tolerance is relevant for cameras mounted in direct sun on plant structures in hot climates.

Downloads & Resources

No downloads available for this product.